Gallagher Aviation now has in its inventory a wide selection of LED beacons for Barons that have the teardrop beacon on the rudder and I can also help replace the belly beacons on Barons and Kingairs.

The teardrop beacon commonly found on the rudder of 58 Barons and some 55s needs to be weighed correctly to be a direct replacement to ensure proper weight and balance of the rudder.

For the top of the rudder I now carry the 9072414 (5 hole mount) LED beacon (https://www.gallagheraviationllc.com/WA ... _p_62.html), which comes in all red. For the belly beacon I carry the 9085204 and the 9085203 (8 hole mount), which are all white and all red respectively. The 90852 series are not required to be weighed exactly like the 9072414 is. These lights are FAA TSO approved.

https://www.gallagheraviationllc.com/LE ... _c_28.html <-- Website Link
1-833-425-5288 <-- Call/Text
513-401-6495 <-- Call/Text/MMS
gallagheraviatonllc@gmail.com <-- Email me here

I just shipped out a 9072414 LED beacon for a 58 Baron today and I have an excellent inventory of them available for immediate shipping today. Below is a link to the beacon.

https://www.gallagheraviationllc.com/WA ... _p_62.html <-- Baron teardrop 9072414 LED beacon light.

James: Thank you for the info on the LED beacon. As I read your post, I take it that I must remove my present oscillating beacon, weigh it, and if it weighs 2.25 pounds, I can do a direct replacement. However, I suppose that I would have to re-calculate a new weight and balance on the aircraft if the old beacon is not the same weight. Is that correct?
In your experience, do most of the oscillating teardrop beacons weigh 2.25 pounds?

Thank you,

Tom

Hi Tom,

Yes that is correct. Or if it has a part number of 01-0790044-57 or 01-0790088014 it will have that 5 hole 2.25 lb weight to it.

I have seen on one occasion where they took the OEM beacon out, installed something totally different that had a different weight, balanced the rudder, and then when the new owner got it we discovered the issues. I was able to find the corresponding LED version so they did not have to re-weigh the rudder.

James

Thank you, sir.

TN

I have an excellent inventory of these LED tear drop beacons. If you have a legacy Grimes beacon on the rudder, the 9072414 is the only LED solution available because it matches the Grimes product for its weight.

https://www.gallagheraviationllc.com/WA ... _p_62.html <-- Baron rudder mounted LED beacon

I also now carry the Astronics LED ground recognition beacon that is found on new G36 and G58 aircraft. This will not substitute the beacon that is found on the rudder of Barons though.

https://www.gallagheraviationllc.com/As ... p_406.html <-- Link to Astronics beacon

James, I have a funny question for you. For replacing the belly beacon on a King Air… Is there a way to compare brightness to the original units? King Airs have flat black paint on the inner lower cowls to reduce glare from the original which wasn’t that bright. And then on a Bonanza I fly, the tail beacon was replaced with a Whelen LED and it’s so bright I turn it off flying at night. Our belly beacon in the king air is failing but if the LED is any brighter I’ll look into seeing if we can’t just rebuild it.

Thanks!

They are brighter but I do not have a good way to measure the difference between the two. If LED is of interest to you, I can quote you your options if I can get the serial number for it. I'd be less concerned with a belly beacon being more bright versus one on the vertical stabilizer or rudder.

Hi Daniel, just my opinion, but for operating at big airports there is no substitute for the old-fashioned rotating beacon on the belly. That red arc making a circular motion on the ground around the plane, stands out better than any flashing strobe when it comes to something bigger potentially running you over.

I do like the old style grimes 2 bulb oscillating on rudder and belly.

Yes the LED would be less power and no issue on motor

I just had two more 9072414 LED beacon lights show up so I can an excellent inventory of them on-hand (4 on the shelf).

https://www.gallagheraviationllc.com/WA ... _p_62.html <-- Link to website

I just shipped out a 9072414 LED beacon for a Baron and I have three on the shelf. I typically keep four of them.

If you have a teardrop beacon mounted on the rudder of your Baron, this is the only solution, far as I know, to go to LED. Add to cart for current price.

https://www.gallagheraviationllc.com/WA ... _p_62.html

I just received three more of these Baron LED beacons. The 9072414 is the correct LED beacon for any Baron with a teardrop beacon mounted on the rudder of the aircraft. If you have a belly beacon, any tear drop with an 8 hole mount should work but feel free to reach out to me to make sure you get it right!

https://www.gallagheraviationllc.com/WA ... _p_62.html <-- Link to website

1-833-425-5288 <-- Call, please leave a voicemail if I do not answer
513-401-6395 <-- Call/Text/MMS, please leave a voicemail if I do not answer
gallagheraviationllc@gmail.com <-- Email me here

I have an excellent inventory of these Whelen 9072414 LED beacon lights. If your Baron or Duke has a tear drop shaped beacon mounted to the rudder, this is the only direct replacement if you do not want to rebalance the rudder.

https://www.gallagheraviationllc.com/WA ... _p_62.html <-- Link to my website

James,

Is this the same part number for the Duke tail beacon? 9072414 28V

Thanks

Mike